Unusual heating technology, fundamentally different from the usual systems with radiators under the windows, has come to us from European countries recently, although it has been used there for more than twenty years. The name of the innovation speaks for itself - a warm baseboard, the demand for it is growing due to technical advantages and modern design.
You will learn all about the varieties of baseboard heating and the features of its operation by reading our article. We will talk about the design specifics and the rules for the construction of all types of baseboard heating systems. Here you will find out where the heating baseboard is used, which models are popular among consumers.
The principle of the plinth heating device
A skirting heater is a heater 140 mm high and 30 mm thick, which is placed along the walls above the floor around the perimeter of the room.
Imagine that the large heating radiator, known to all of us, was reduced and stretched - a simplified design can be described just like that.
The required power is collected from heating sections of different lengths, a warm baseboard not only heats the room, but also dries the wet bottom of the walls and corners
Materials for production are used the most thermally conductive and, accordingly, expensive - aluminum, copper, brass. Externally, the thermo skirting board is an aluminum box, a heating element is placed inside it - two copper tubes with brass, copper or aluminum plates (lamellas) strung on them.
The outer diameter of the tubes is 13 mm, the inner is 11 mm. The heating modules are joined together, the joints are connected by copper soldering or crimping nuts, in the corners special turning parts are used - polyethylene or copper
Depending on the coolant, there are liquid and electric warm skirtings:
- in liquids, water or antifreeze circulates, 0.34 liters of liquid per 1 meter, the temperature range is from 50 to 85 ° C, the temperature is set manually on the collector or automatically;
- in electric heaters are connected in parallel, their work is regulated by a temperature regulator with a built-in temperature sensor that determines the degree of heating of the air in the room.
The heating modules are mounted on the rear aluminum plate, which is attached to the wall directly above the floor. Outside, the structure is closed by a front plate - also of aluminum.
The coolant is supplied from the distribution manifold. The distribution manifold is equipped with flow meters, taps (drain, shut-off), automatic air vents, thermometers, manometers - all this is necessary to control and adjust the heating system. Safe heating of the plinth surface is 40 ° С, maximum - 80 ° С, the air in the room warms up to 20-24 ° С.
Slots are provided in the lower and upper parts. The cold air stream enters from below into the body, heats up there, passing between the hot plates, and again goes outside, but through the upper slot.
In the water thermal baseboard, the coolant moves inside the heat exchangers through tubes, and in the electric heat carrier, the heating cable, laid in the same way, performs the function of the coolant
Manufacturers of baseboard heating equipment claim heat transfer within 200 W per 1 meter of length, but in order to achieve this indicator in a liquid system, the temperature of the coolant must be raised to 65 ºС, and such a front panel heating can not be called safe.
Image Gallery
Photo from
A warm baseboard is an excellent solution for arranging rooms with panoramic glazing: verandas attached to the house, loggias in the attics, halls of private houses and public places
Installation of a heating plinth allows you to perfectly mask the presence of a heating system
Installing a warm baseboard allows you to remove radiators where they really will interfere, but at the same time provide room with heat
There are no restrictions for installing a skirting heating system. It can be mounted in city apartments, country houses, shopping, sports complexes, medical facilities, kindergartens
The heating baseboard version can serve as the main source of heat and can be used as a complement to the radiator circuit
The plinth heating circuit provides a uniform supply of heat to the room, while saving energy
The heating plinth fits perfectly into any design decision, combined with wooden walls and all kinds of finishes
Plinth heating circuits occupy a minimum of space, therefore they are actively used in small rooms, in narrow hallways, on equipped loggias
The heating plinth in the arrangement of the veranda
The best way to hide the heating system
Safe heating system option
Plinth heating system in the apartment
Application as a Supplement
Uniform heat distribution system
Compatibility with any interior design
Miniature system dimensions
Features of baseboard heating
Heating from the moment of its invention to the present day is divided into two types - convection and panel-radiating. In the first case, the air is heated first from the hot surface of the heater (radiator battery, convector), after which it circulates in the room and gradually heats it.
In the second case, objects are initially heated in the room, and air is heated from them by useful infrared radiation that does not dry the air, does not corrode oxygen from it, and this process is secondary.
Among long-standing examples are stoves in village houses, tiled stoves in old mansions, in the modern interpretation - heated floors, but what about plinth heating and what type of heating can it be attributed to?
Heating a room using a warm baseboard allows for a uniform heat supply in height and area of the treated room
Let us turn again to the opinion of manufacturers. They unanimously claim that the radiated heat along the perimeter rises from the floor to the ceiling along the walls, warms them evenly and creates a kind of curtain from the cold penetrating from the outside. Having warmed up enough, they themselves begin to give off heat.
In fact, the temperature of the walls at different heights ranges from 26-30 ºС, and in order for heat transfer from them, the surface must be heated much more. Consequently, talking about the coveted infrared heat coming from the walls is not so much true as a marketing ploy.
The planes of thermal skirting boards emit maximum heat at the level of the legs. It is not only pleasant, but also optimal for well-being and health (+)
It is more correct to say that thermal skirting boards are also convectors with a high surface temperature. It’s just that the room warms up more evenly from the warm air currents, both directly emanating deep into the room, and so ascending along the walls. Warmed walls are a guarantee that you will not find dampness or mold anywhere on them.
It is also fair to note that as you move up, the amount of heat decreases, and that’s good. It is evenly distributed indoors in the lower and middle zones, to a lesser extent reaching the ceiling. For people, such a microclimate is considered the most comfortable - they do not freeze or chill, but at the same time breathe fresh and cool air.
Objectively about all the advantages and disadvantages
The rising heat flux, according to the physical law of Coanda, is pressed against the wall. Without mixing with the rest of the air in the room, it heats the vertical surface. At a height of up to one and a half meters, the wall temperature is several degrees higher than in the room, and this creates thermal comfort for the people in it.
During the heating season, the heating system is activated for 6-8 hours daily. Multiplying the total capacity by the number of hours worked per month, we get the indicator of monthly energy consumption.
The distribution manifold evenly distributes the coolant in the individual circuits. His choice is determined by a number of factors - the product material, comb capacity, pressure, power consumption, the possibility of further expansion
Do skirting heaters really save energy due to the low temperature of the coolant?
The answer would be an example:
- The area of the room is 3, 5m x 5m (17.5 sq. Meters), the perimeter is 17 m (minus the doorway - 16 m).
- The volume of the room with a ceiling height of 2.7 m: 17.5 * 2.7 = 47.25 cubic meters. meters
- Outdoor temperature in winter is -10 ºC on average.
- To maintain + 20-22ºC in a room with normal thermal insulation, 1.5 kW / h is required. Heating will work 7 hours a day.
Taking into account 200 W per 1 meter of length when heating the coolant to 65 ºС (see above) we get 200 W * 16 m = 3200 W or 3.2 kW. Since this flow rate is twice as high (3.2 kW / 1.5 kW = 2.1), it is possible to reduce the temperature of the coolant in the same proportion: 65 ºС / 2.1 = 31 ºС.
We calculate the monthly electricity consumption: 1.5 kW / h * 7 hours. * 30 days = 315 kW. More reliable results are provided by a detailed thermal engineering calculation based on complete source data for the facility.
If we compare the effectiveness of the warm floor and skirting board, then we can argue for the very reason that convectors from the floor immediately heat the air, and part of the warm air from the thermo skirting board is taken over by the external wall, which is constantly fed by cold from the outside.
The heat spent on constant heating of cold external walls is a kind of loss. Is their dryness, lack of mold, dampness a compensation for this? There is also a debate on this issue: some say yes, others indicate that the humidity in the room is regulated by supply and exhaust ventilation, and not by heating.
If the water radiators are connected in series, the coolant will cool down, bypassing the entire perimeter. Therefore, the modules are combined in parallel, each pair of inlet and outlet pipes is separately output to the collector
As for the appearance, the baseboards that cover the heating look really nice in the interior, but there are problems with cabinet furniture - you can’t go around it in front, and behind it the warm air has no freedom of movement.
And about the absolute absence of dust in the air, it is worth arguing - it may be less than with air circulation in traditional heating systems, but it is, because convection is present.
In general, we can conclude that skirting radiators already have buyers, and over time their number will increase. The limiting factor is the excessively high cost of equipment, which is explained by the use of copper, brass, aluminum, i.e. expensive materials.
And installation, if ordered from professionals, is not cheap. Plinth layout of pipes is the most difficult of all available water heating circuits, but there are many nuances in the assembly of electric skirting boards.
Installation of a warm skirting board
For installation, you will need a tool: adjustable wrenches in a set, a drill with a shock function (or a perforator), a hammer, nippers, pliers, scissors (cut plastic). The plinth heating system is quickly mounted if the connection points are prepared in advance.
Even before purchasing the necessary equipment, you need to plan how much heating elements are needed and how to place them around the perimeter of the room.
Assembling a water heating system
Stage 1. We measure the distance from the point where the distribution manifold will be located to the location of the baseboard. We cut off two lengths of the protective pipe and two with an allowance of 20 cm - the connecting one. We insert the connector into the protective one, cork the ends with adhesive tape to protect it from dirt.
Installation of a plinth heating water system: red - main flow, blue - reverse. The return pipe must be above
Stage 2. Pipes are pulled along the floor without tension so that, if necessary, building next to one another could be laid. We fix with mounting tapes, cover with a protective solution, protecting from damage, and put it in the right place on the wall 6 cm above the floor and 10-15 cm from the edge of the wall or corner, fix it with cement.
Stage 3. After laying the final floor, we continue to work. We stick an insulating strip along the entire length. We stretch the aluminum edge (also along the entire length of the heating), closing the junction of the wall and floor. Screw it on or fix it with duct tape, silicone.
Stage 4. We lay a special profile on the top line, we put holders on it at a distance of 15 cm from the corners and every 40 cm along the wall.
Stage 5. To connect the heating pipes and heating elements, we use couplings with nuts, bushings and gaskets, in the corners - angular swivel tubes 90º, in the ends - end swivel tubes 180º and plugs. Thermosexuals are interconnected by adapters.
When attaching the heating module, it is necessary to remove 2-3 lamellas from the edge and put on the tubes connecting nuts, crimping parts, rubber gaskets
Stage 6. Carefully press the connected heating sections into the holders. We put on decorative panels (fasten with screws or snap in) and decorative corner elements. We connect the system to the collector, fill the water, test at operating and maximum pressure.
Like all collector systems, the heating skirting requires a circulation pump that stimulates the movement of the coolant. Without a pump, heated water is difficult to circulate along an extended circuit. However, the use of technical devices affects the total cost of the system.
The skirting board will work if all technological operations were performed without violations. When leaking, problematic connections must be squeezed with a wrench. The coolant is supplied through the collector by a circulation pump from the boiler or from a common (centralized) heating system.
Assembly of the electric heating system
For a warm baseboard in an electrical panel, you need to make a separate circuit breaker. Its power is determined by the number of heating modules.
Stage 1. We bring power to the junction box, which should be next to the location of the system at a height of 4-6 cm from the floor.
Installation of an electric heating system: most often the electric system is used where it is possible to supply the required power, or in small spaces as additional heating
Stage 2. Glue the insulation tape on the wall.
Stage 3. We install the lower aluminum profile (edge) and the upper one, on which we mount the holders at the same distance as for the water system - 15 cm from the corners and in increments of 40 cm along the wall. We mount an external temperature regulator. It should be located at a height of about 1.5 m opposite the system modules and at a distance of at least 2 meters from them.
Stage 4. We insert electric heating elements (TENs) into the lower pipe of the heating module, we fix the modules in the holders so that they do not touch the wall.
The electrical contacts of the heating elements are threaded, two nuts, a snap ring on the spring, a heat shrink tube for additional insulation. The modules are connected in parallel with a heat-resistant power cable with silicone coating and heat resistance up to 180 ° C.
Stage 5. We close the system with a plastic box on top.
To connect the heating modules, a 3-core cable is used: brown core - phase, blue - zero, green (yellow) - grounding. It is necessary to ground the cable
It is better to entrust an electrician to connect the installed heating system to the power supply. He will check the reliability of the insulation with measuring instruments, supply electricity and adjust the thermostats.
Design, scope, price
Thin, elegant heaters, in harmony with the general environment, allow you to realize the most non-standard design ideas.
The peculiarity of the plinth heating system is that it does not completely take away free space from the room, and it can be placed next to furniture, antique items, household appliances, musical instruments.
The material from which the flooring and walls are made does not matter either - there will be no damage or harm.
A palette of hundreds of colors and shades makes it possible to choose the appearance of the case to your liking. By texture, it can be a flat and smooth surface or imitation of granite stone, marble, wood.
The plinth radiator equalizes the temperature in the cooler corner and end rooms, the owners of cottages and country houses are interested in this technology, seeking to create an elegant interior in their homes. And in high-rise buildings, many people want to make heating of loggias, balconies, and this task is also easily solved with the help of a similar heating scheme.
Wherever plinth heating is used - in greenhouses and conservatories, pools and gyms, in museum buildings, concert halls, etc. Panoramic construction is in fashion, but along the wall, which is solid glass, you can’t put ordinary radiators.
An extensive range of textures and shades of the body of the warm skirting board allows you to use it as an element of decor. In this case, it merged into a single unit with the door trim
Traditional heating loses in rooms with high ceilings. No matter how much you heat them with batteries, warm air will still tend to rise up to the ceiling, leaving the lower zone cool, and with the help of a thermal baseboard, the situation can be easily fixed.
As for the price, the purchase and installation of a warm skirting board is comparable to the cost of underfloor heating. Both that, and another will not manage cheaper than installation of a classical heating system with batteries.
Unfortunately, all energy-efficient devices cannot be called cheap, but the costs pay off. In order not to overpay the excess, you need to pre-assemble the system - each of its elements has its own price. Only a specialist can do this competently.
Video # 1. How does a warm skirting board work:
Video # 2. Installation of baseboard heating system:
To summarize: a warm baseboard is a new, aesthetic and reliable type of heating equipment that deserves attention.
Want to talk about how you assembled and mounted a skirting radiator? Do you want to share your impressions of the operation of baseboard heating or ask a question? Please write comments in the block below.