You can arrange heating and hot water supply of a private house in various ways, for example, connect to the central gas supply communications or transfer heating systems to electricity consumption. Do you agree?
And you can assemble a geothermal heat pump with your own hands and effectively use the heat of the earth to create comfortable living conditions. Of course, this is a rather time-consuming process, but for those who are at least a little versed in technology, it will not be a big deal.
In our article, we will talk about the principles of operation and types of geothermal installations. We will tell you how to build a heat pump yourself from improvised materials. In addition, in the article you will find expert advice on choosing geo-aggregates. And the videos posted will reveal the secrets of installation and the principles of operation of geothermal pumps.
How does a thermal geo unit work?
The algorithm of the geothermal heat pump is based on the transfer of heat from a source with a low potential of thermal energy to the coolant. The land here plays the role of a radiator in the summer and is an active source of heat in the winter season.
Soil temperature differences help improve overall system efficiency and help reduce actual operating costs.
The basis of the geothermal heat pump is a phenomenon such as thermal inertia. The temperature of the earth at a depth of 6 meters and below almost exactly corresponds to the average annual air temperature in the region and changes very little throughout the calendar year
In practice, the existing coolant enters the pipeline located in the ground and heats up several degrees there. Then the composition goes to the heat exchange unit (or evaporator) and transfers the accumulated thermal energy to the internal system circuit.
The principle of operation of geothermal installations is similar to the functioning of refrigeration systems. That is why some types of heat pumps in the summer are successfully used as air conditioners and with their help they cool the air in residential premises
The refrigerant operating in the external circuit is heated in the evaporator, converted into gas and enters the compressor. There, it contracts under the influence of high pressure and becomes even hotter.
The hot gas passes into the condensation device and gives off thermal energy to the working coolant of the internal system responsible for heating the house. At the end of the process, the refrigerant, which has lost heat, returns to the starting point in the liquid state.
What are geothermal installations?
Geothermal heat pumps differ from each other in the type of heat carrier on the internal and external contours of the structure. The energy of the device is obtained from soil, water (groundwater or an open natural reservoir) or air.
Inside the premises, the heat resource is used for heating rooms, heating water and air conditioning. Depending on the combination of elements and functions used, the systems are classified into types: “ground-water”, “water-water” and “air-water”.
Option 1. Land-to-water assembly
The ground-water pump is one of the most effective alternative heating options for residential buildings. The principle of its action is to select, using probes or collectors, thermal energy from the soil and transfer it to a home water heating system.
Ground-to-water geothermal heat pumps are high-tech, progressive devices. They are characterized by exceptional reliability and demonstrate a high level of efficiency. Do not require constant intervention of the owners in the work, but need professional after-sales service
The special installation, consisting of a geothermal heat exchanger located below the depth of the actual freezing of the soil, and the heat pump itself, which functions as a refrigerator, helps the technology to realize it, only the other way around (the Carnot reverse cycle).
How the device works
The ground-water installation, which heats the living quarters due to the renewable heat produced by the soil, operates according to the following algorithm:
- The working fluid (brine or antifreeze), moving along the geothermal circuit, takes the temperature of the soil and is transferred to a heat exchanger - evaporator through a pump. There she gives the collected heat to freon, and herself, becoming colder by 2-5 ° C, returns to the starting point.
- Enriched with thermal energy, freon evaporates and, having taken a gaseous state, enters the compressor unit. There, the temperature of the gas rises due to compression and condensation forms.
- Thermal energy is transferred to the coolant in the home heating system, and freon again takes on a liquid form. Its pressure drops after passing through the expansion valve of the system and the refrigerant is returned back to the evaporator to gain another portion of the resource.
As a result of this procedure, the amount of thermal energy taken from the soil and transferred to the heating system of the residential building is more than 4 times the amount of electricity expended to ensure the correct operation of the compressor unit, the circular pump and the control unit.
A glycol mixture with a good viscosity index, water with alcohol or saline are precisely such non-freezing liquids that are used in the earth-water system. They are environmentally friendly, efficiently take heat and transport it to the pump station
An additional bonus is the fact that the system has the ability to work in the opposite direction, that is, for cooling. True, the loss of efficiency reaches 20%, but this is considered justified, given the high heating ability of the equipment.
Land-to-water placement options
To create the outer contour of the earth-water system, polymer pipes of high strength with good performance are used. They are placed horizontally, laying at the bottom of the pit in a manner reminiscent of the arrangement of communications for “warm floor” complexes.
The ground-water heat pump is reliable, efficient and quiet in operation, however, its installation costs decent money and takes a lot of time (at least 1 month for construction, installation and commissioning activities). This point must be taken into account before deciding on a heating system of this type
During installation, an area of 25-50 square meters is used. m for each individual kilowatt of power mounted pump. The depth of the pit is chosen below the freezing boundary, and the exact dimensions and the pitch of the pipe laying are determined by an additional calculation.
It is advisable for owners of large-sized land holdings who have chosen a ground-water geothermal heat pump to heat their home, to install horizontal collectors. The owners of small plots are more likely to install deep probes, since they go far into the soil and do not “eat up” the useful area near the house
Territories on which communications of land-water geotreme systems are arranged are no longer used for agricultural purposes. They can be broken into a beautiful grassy lawn or flowerbed with blooming annuals.
Vertical installation is much more problematic and entails the use of professional equipment. A well from a depth of 20 to 150 m is drilled at the site using a drilling rig, a special geothermal probe is lowered into it and connected to a pump that supplies the working fluid to the home heating system.
The vertical probe for the earth-water geothermal system is a head with connected pipes. It is immersed in a well with a depth of 18 m or more. The exact number of wells and probes, the depth of the required immersion, and the actual diameter of the pipeline are calculated separately for each particular case, based on information obtained as a result of geological exploration by specialists at the site
Probe tubes extending from drilled wells enter the manifold well. From it to the heat pump there are 2 trunk lines (supply and return), equipped with insulation coating. The diameter of the line depends on the total volume of the system and the room that you want to heat. Sometimes the parameters reach 160 mm.
According to rough estimates, about 7.5 kW / h of energy will be needed to heat a residential building with an area of about 100 m2. In this case, the vertical probes for creating a heating system “land-water” will have to be lowered into the ground by 110-115 meters, or taken under horizontal communications 250 m2 of the adjacent section (+)
Due to the fact that at a depth the soil temperature is always higher and more stable due to the influence of the earth’s core, the vertical way of laying the heating system is recognized as the most effective. It demonstrates a high level of efficiency and reliably works for many years, without giving failures and breakdowns.
Option # 2. Features of water-to-water heat pumps
The water-water geothermal system uses the thermal energy of a water resource in its work. This is possible because, at great depths, the temperature of the water, like the soil, remains quite high and maintains stable, constant indicators throughout the year.
To equip the water-water system and obtain low-potential heat energy, you can use open water bodies (lakes, rivers), wells, wells and even wastewater from technological cycles of industrial production (reverse water supply)
There is no fundamental structural difference between a ground-water heat pump and a water-water heat pump. But the smallest financial and labor costs require a complex equipped on the basis of an open reservoir. Installation does not require large-scale drilling activities.
The pipe material with a coolant is simply equipped with a load, immersed in water and connected to the home heating system through connecting communications.
However, this option is only possible if the land is adjacent to the water and all communication parts of the system are under the control of the owners. If there is no access to an open reservoir, the potential of groundwater is used.
True, this entails serious land work and the construction of complex structures, for example, an additional well designed to discharge water passing through the heat-exchange unit.
When installing a water-to-water heat pump, not one, but two wells are equipped. Working water is taken through one and, having passed the heat exchanger, is redirected to the second, which is located in the direction of movement of the ground flows. During the placement, it must be taken into account that the receiving well must be at least 6 meters from the producing well and must be downstream
Typically, water-to-water installations are installed where it is not possible to connect central communications or use other types of coolants.
Experts say that alternative heating of this type is extremely effective in modern buildings with a minimum heat loss rate.
In the manufacture and installation of do-it-yourself water-water geothermal heating systems, it is very important to use materials with a high level of resistance to corrosion, freezing and other aggressive manifestations of the external environment. Then the equipment will last a long time and not give the owner any trouble
If the house is well insulated, protected from drafts, dampness and the ingress of frosty air or built using modern thermal insulation technologies, the cost of the heating system is significantly reduced due to the opportunity to purchase pumping equipment of much lower power.
Option # 3. Arrangement of air-water systems
The air-to-water heat pump uses the most affordable, unlimited and renewable natural energy resource — air — for operation. The equipment operates through fans and evaporators, combined into a single complex.
It is most effective at temperatures up to -15 ° C. With more aggressive indicators, it loses a significant part of the power.
The air-to-water heat pump costs significantly less than the water-to-water and ground-to-water models. The module is suitable for regions with relatively warm winters. In cold northern regions where frosts exceed -20 ... 25 ° C, installation of air equipment is considered inappropriate
The unit is extremely convenient in that it does not require the owners of a private home to have special equipment for installation and complex installation work.
It does not need excavation, well drilling and other labor-intensive measures. Easy to install and does not take up much space. It can function correctly, located on the roof of the living room.
It is possible to install an air-water geothermal pump on a site directly near residential buildings. It works quietly and has a modern attractive appearance, not spoiling the overall design of the territory
The main advantages of the equipment include almost silent operation and the possibility of reusing heat released from the heated room in the form of exhaust air, water, gas, smoke, etc.
Owners carry out system maintenance on their own:
- clean the fan blades and protective grilles on the evaporator installation from dust, fine debris and leaves;
- lubricate compressor special composition specified in the manufacturer's instructions;
- change oil in power units (fan, compressor) with a certain frequency;
- check the integrity of the power cable supply and copper piping through which the refrigerant circulates in the system.
In addition to these actions, manufacturers of pumping equipment strongly advise customers to monitor the condition of thermal sensors that reflect the operation of the control unit.
They must be cleaned by gently removing dust and oil stains from the surface. This will extend the “life” of the air-to-air system and make the operation process simpler and more comfortable.
How to make the unit with your own hands?
Regardless of which resource option (earth, water or air) is selected for heating, a pump will be needed for the system to function properly.
This device consists of elements such as:
- compressor unit (intermediate element of the complex);
- evaporatortransmitting low potential energy to the coolant;
- throttle valvethrough which the refrigerant finds the return path to the evaporator;
- capacitorwhere freon gives off thermal energy and cools to the original temperature.
You can purchase a complete system from the manufacturer, but it will cost a decent amount. When there is no free money at hand, you should make a heat pump with your own hands from the parts available and, if necessary, buy the missing parts.
When planning to install a geothermal heating system in a private house, you first need to take care of reducing the level of heat loss. For this, the walls must be insulated with special material, the doors and window frames should be provided with foam paddings, and the floor and ceiling should be protected with foam panels.Then the heat allocated by the pump to the maximum extent will remain indoors
When the decision to make a heat pump with your own hands is made, you must definitely check the condition of the electrical wiring and the meter available in the house.
If these elements are worn and old, you need to look at all the areas, detect possible malfunctions and eliminate them before starting work. Then the system immediately after startup will work flawlessly and will not disturb the owners with short circuits, fire wiring and knocking out traffic jams.
Method # 1. Assembly from the refrigerator
To assemble the heat pump with your own hands, remove the coil located at the back of the old refrigerator. This part is used as a capacitor and placed in a high-strength container that is resistant to aggressive temperatures. A well-functioning compressor is attached to it, and a simple plastic barrel is used as an evaporator.
If a very old refrigerator is used to create a pump, it is better to replace freon in it with a new one. You won’t be able to do this on your own, so you will have to invite a master with special equipment. It will quickly replace the working fluid, and the system will work in the right mode
The prepared elements are interconnected, and then the created unit is connected to the heating system by means of polymer pipes and the equipment is put into operation.
A step-by-step instruction on how to assemble a heat pump from a refrigerator is described in this article.
Method # 2. Air conditioning heat pump
In order to make a heat pump, the air conditioner is modified and some basic units are redeveloped. First, the outer and inner blocks are interchanged.
The evaporator, which is responsible for the transfer of low-grade heat, is not additionally installed, since it is available in the indoor unit of the unit, and the heat-transferring condenser is located in the outdoor unit. Both air and water are suitable as a heat carrier.
If this installation option is not convenient, the condenser is installed in a separate tank designed for the correct heat exchange between the heating resource and the heat carrier.
The system itself is equipped with a four-way valve. A specialist with professional skills and experience in conducting events of this kind is usually invited for this work.
Modern split systems are ineffective at low temperatures, so professionals do not recommend using them for the independent manufacture of heat pumps
In the third version, the air conditioner is completely disassembled into its constituent parts, and then the pump is completed from them according to the traditional conventional scheme: evaporator, compressor, condenser. The finished device is connected to the equipment heating the house and begin to use.
The site has a series of articles on the manufacture of heat pumps with their own hands, we recommend that you read:
- How to make a heat pump for home heating yourself: the principle of operation and assembly diagram
- How to make an air-water heat pump: device diagrams and self-assembly
System Tips
Installation of land-water equipment is more expensive than all other options, because it requires deep excavation work with a vertical arrangement of equipment or a large free area of a site with horizontal laying of communications.
These parameters limit the use of the system and significantly reduce its attractiveness.
Installing a water-to-water pump also has some limitations. If there is an accessible body of water nearby, you can place the system in it. The lack of open water will entail the drilling of wells and bypass wells, which is also not cheap.
The air-water pump does not present installation problems, and can work correctly even in apartment buildings, but in severe winters with low temperature indicators its efficiency decreases and a parallel energy source is required to support it.
However, the arrangement of geothermal heating ultimately pays off its costs and begins to generate a free resource, allowing owners to live in the most convenient, pleasant and comfortable conditions, without spending a lot of money on utility bills.
The video illustrates how a heating system based on geothermal air-water heating equipment is equipped in a large house from a gas-silicate block. Some interesting nuances regarding the installation of equipment are disclosed and the real numbers of utility bills for the month are announced.
How does ground-water equipment work? A detailed description from a specialist in the installation of geothermal thermal boilers, recommendations and useful tips for home masters from a professional in their field.
A real user of equipment shares his impressions of the thermal geothermal pump.
A professional locksmith tells how to make a heat pump at home based on a powerful compressor and tubular heat exchange parts. Detailed step-by-step instructions.
A geothermal pump for heating a private home is a good way to create comfortable living conditions even where centralized communication systems and more familiar sources of energy are not available.
The choice of system depends on the territorial location of the property and the financial capabilities of the owners.
Have experience manufacturing a geothermal heat pump? Please share information with our readers, suggest your version of the assembly. You can leave comments and attach photos of your homemade products in the form below.