It is not necessary to repair Bosch dishwashers, which are under warranty, on their own. It is better to notify the service center about the situation and wait for the wizard to arrive from there and fix all the problems.
If the warranty period has expired, you can try to fix some problems with your own hands, having previously determined the causes and the location of the malfunction using the alphanumeric code. And what kind of fault does this or that code correspond to and what steps can be taken in a specific situation? We will talk about this in detail in our article.
Common Error Codes
The latest lines of kitchen appliances of the German concern are equipped with a progressive self-diagnosis system. It monitors the correct functioning of the devices, and all Bosch dishwasher error codes are immediately displayed on the LCD in the form of an alphanumeric abbreviation.
Typical malfunctions, which are considered characteristic of Boshevsky units, are indicated by the English letter "E" and one or two digits. This facilitates the troubleshooting process, allows you to understand what exactly happened to the equipment and how to fix this situation.
The display has a bright, noticeable and clearly distinguishable indication. The error code appearing on it looks clearly, and it is not difficult to consider it correctly. In case of fixing a serious problem, the program turns off the machine
In some models, instead of the letter “E”, “F” is used, and the digital indicator remains the same.
Code Group # 1 - Water Heating Complications
E01 indicates damage to the heating element or violation of the structural integrity of the heater circuit. Most likely, this element burned out, and for further correct operation a replacement of the heating element is required. In parallel, you should check the temperature sensor and make sure that it is able to provide reliable information.
E2 sometimes alternately with E01 pops up on the home screen. Usually this indicates that the internal water temperature sensor is faulty. In this embodiment, the heater will operate at full power, as indicators of the level of heating will not be able to enter the control unit. If the problem is not resolved in time, the problem will overload the heater and cause it to burn out.
To establish the malfunction of the temperature sensor, it is necessary to check the resistance level at its contacts. Typically, this element has a baseline of about 55 kΩ at 21 ° C. Deviation to lower values clearly indicates a breakdown.
E09 signals problems with the flow heater. Most often, this error is recorded by models with a heating element located deep in the circular pump. To solve the problem, it is necessary to conduct a detailed diagnosis of the heating element using a multimeter. If the resistance is at zero, the heater will need to be replaced.
E11 says that the temperature sensor does not receive power, for example, due to a communication failure between it and the control module.
Several reasons provoke this at once, so the user will have to check for damage to such nodes as:
- working contacts of the temperature sensor;
- wiring from the temperature sensor;
- contact elements of the control module.
When visually detecting problem areas, the machine will need to be disconnected from the power supply and only then proceed with troubleshooting.
E12 it is displayed on the display of the dishwasher at the moment when the heating element is overloaded as a result of the subsidence of a large amount of dirt on it or the occurrence of scale. After rebooting the dishwasher, the code sometimes changes to E09, but regardless of the numbers, it indicates the same problem.
From dirt and scale TEN can be cleaned at home. However, in order to get to it, the dishwasher will need to be partially disassembled, the heating element removed, the dirt removed and then the item returned to its place
During repair work, it is necessary to strictly observe the basic safety rules and be sure to disconnect the device from the power supply to avoid personal injury and burns.
Code Group # 2 - Blockage Issues
The formation of various kinds of blockages is a weak point in all respects for Bosch reliable and high-quality kitchen washing equipment. These unpleasant moments occur, usually due to the fault of users who neglect to remove food residues from the dishes before loading into the washing unit.
E7, highlighted on the display, stands for "the inability to pump water from the tank as a result of clogging of the drain hole."
There may be several reasons for this situation, for example:
- improperly laid dishes;
- an object blocking the water outlet;
- clogging of the drain with food residues, fatty deposits.
To eliminate the error code, it is enough to fold the dishes more neatly, remove objects that are potentially capable of blocking the hole for draining water, and clean the surrounding area from anything that interferes with the outflow of liquid. After these actions, the unit will work again in normal mode.
Even if the Bosch machine is functioning properly, it is better to monitor the cleanliness of the filter, trying to prevent its contamination. This simple procedure will help to extend the life of the unit and ensure high-quality washing of dishes throughout the entire operational period.
E22 usually indicates contamination of one of the unit’s internal filters. In this case, it is necessary to replace the clogged filters with new ones. The same code is sometimes displayed in case of problems with the drain pump, for example, in the case of a decreased impeller rotation speed. A deeper diagnosis is required here, similar to troubleshooting E21.
Error with code E24 for dishwashers of the Bosch brand, it stands for kink, crease or clogging of the drain hose, pollution of the sewer drain or overlapping of the drain outlet at the siphon. The causes can be very different, and often this abbreviation arises in parallel with E22.
If the fault of E24 is a clogged or wrinkled hose, it is advisable to replace it with a new one as soon as possible. Choosing is worth a durable, service-resistant element of the appropriate dimensions
Eliminating the problem of such a plan is not difficult. Simply visually detect one of the above problems and fix it yourself or with the help of a service center employee.
E25 gives a signal that food waste and other waste elements that impede the passage of water have accumulated in the pipe section of the pump or in the base of the drain hose. As a result, the pump power decreased, and he lost the ability to fully divert the used liquid to the drain.
If E25 and E22 alternately light up on the screen, you need to remove the dishes, allow access to the impeller of the pump and see if food waste has wound around it. Perhaps it is they that slow down the movement
The following situation - the corresponding sensors caught the problem and sent data to the control unit of the unit. As a result, the abbreviation lit up on the display. E25, and the dishwasher ceased to fulfill its direct functions.
To eliminate the malfunction, it is necessary to disconnect the device from the power supply and the water supply system, carefully clean the pipe and drain hose from sediment and blockages, while at the same time checking the impeller of the pump for entanglement with foreign waste elements.
A video with instructions for fixing error 25 will help independent masters cope with the task:
Code group # 3 - problems with water collection / discharge
E3 stops the machine when, within the framework of a specific program, it is not possible to draw water into the chamber for the allotted time period. In the latest Bosch models, in this situation, self-draining of the working fluid is first carried out, and only then an alphanumeric trouble code appears on the screen.
In products without display, released 7-10 years ago, the process is the opposite. If the Bosch dishwasher displays an error "Crane", first the problem is solved, and then the tank is filled with liquid.
Poor condition, kinks and breakage of the hose connecting the home assistant to the plumbing system can prevent liquid from entering the washing chamber. If this is the case, the element must be carefully disconnected and replaced with a new one.
To solve the problem, it is required to check the presence of water in the central supply system. If everything is okay with this, you should pay attention to the filters located at the entrance to the dishwasher immediately before the inlet hose and establish the correct operation of the valve and the water level sensor. In the end, you can look at how the pump works, because sometimes it is it that provokes the appearance of the E3 error code on the screen.
E5 gives a clear signal that the unit tank is full of water. This happens when the water level sensor fails and cannot stop the filling process at the right time. To eliminate the problem, it is necessary to carefully inspect the sensor and find out if its tube is clogged with dirt and food debris, if the working contacts are melted and if the wiring is burned out.
If everything is fine with the indicated nodes, it is worth dealing with the filler valve. Perhaps, for some reason, it cannot completely close and block access to the tank.
Sometimes the cause of the E5 code is a malfunction in the control unit of the dishwasher. It is extremely undesirable to fix such problems on your own. It is better to entrust the work to a qualified specialist from the Bosch service center
E8 in many ways it is similar to the E3 error and behaves exactly the same way - the dishwasher does not collect the required amount of water into the pan. Because of this, the circular pump cannot turn on correctly, and the heating element loses its ability to join the work. The search for the causes of the malfunction is carried out according to the principle described for the E3 code.
E16 indicates the inability of the equipment to block the access of fluid to the washer reservoir. Water is poured into the car uncontrollably, contrary to the established regime. Typically, this situation is triggered by the entry of debris into the intake valve. Large particles do not allow the partition to close tightly, and water continues to seep inward even with the machine idle.
To fix the problem, carefully inspect the filling valve, remove large particles of dirt and clean the surrounding area. Then you need to check the health of the water level sensor and find out if there is any excess foam in the tank from the detergent.
E17 signals about incorrect filling of the dishwasher with water. This type of error is more rare and narrow-profile. Usually this is due to the inlet valve, with a large force blocking the water or not able to close at all due to excessive fluid pressure. Then it is necessary to partially block the water on the riser pipes, thus lowering the total pressure in the system.
In case of general malfunctions in the water or electricity supply system, an error code can also be seen. In this case, it is enough to reboot the equipment, and it will return to normal, stable mode of operation
Sometimes the appearance of the E17 code is provoked not by mechanical problems, but by failures of a completely different nature, for example, water hammer.
If the malfunction is not detected, it is appropriate to check the sensor, which measures the amount of water supplied to the tank. Perhaps the problem lies precisely in it and specifically this element is the reason for the appearance of the E17 code on the screen.
E21 draws the attention of the user to the fact that the pump of the machine stops working correctly, preventing the unit from draining water in a timely manner. A situation is created when the power to the pump is supplied in full, interaction with the control unit and sensors occurs in normal mode, but drainage is not carried out and water remains in the tank.
In search of a problem, it is worth checking the impeller. Perhaps it stopped rotating due to the fact that some foreign elements were wound on the base or blades and jammed the correct movement. Or the rotor adhered to the walls of the sleeve, and it must be well cleaned and greased. Sometimes this is evidenced by a change in the error code value from E21 to E22.
Replacing the pump in Bosch dishwashers is perfectly acceptable, but only with the original part with the exact same factory marking that stood on the faulty appliance. Otherwise, you should not count on the quality of the module
But most often the problem is the operational wear of the pump mechanism, which interferes with the pumping / pumping of working water. The solution is simple - you need to remove the old pump and replace it with a new one.
Code Group # 4 - Electrical Failures
The electrical system of modern Bosch units consists of a large number of various sensors and fittings. One burned-out terminal or frayed short wiring create a lot of difficulties and make the screen glow with different error codes.
E01 and E30 talk about failures in electrical or electronic systems. The easiest solution is to reboot the unit through the on / off activation button. If the error indication disappears, then an elementary failure has occurred and operation can continue in normal mode.
You can try to identify the cause of the malfunction in the electronic dishwasher system yourself. However, it will take a lot of time, since the homemaster will have to conduct a visual check of all the wires and terminals that are in the device
When the error codes repeatedly continue to be displayed, you must contact the service center and invite a qualified craftsman to your home. He will carry out diagnostics with the help of special devices, identify and eliminate the detected problems.
E27 usually “pops up” in those machines that are directly connected to the electrician. The abbreviation appears on the screen after voltage surges that have occurred on the network. If the code becomes a frequent occurrence, you should buy a stabilizer and connect the dishwasher through it, thus protecting the unit from possible short circuits.
Code Group # 5 - Breakdowns of Switches and Sensors
Sensors and water switches help control the operation of the dishwasher and control the execution of various programs. When these parts break down, the internal diagnostic system recognizes this and displays error codes describing the problems on the display.
E4 reports that the control sensor, which is responsible for the pressure and flow of water flowing into the sprayer, does not cope with its functions. The reason lies in a mechanical malfunction or blockage. Perhaps too hard running water clogs the nozzles and no fluid flows through them. Cleaning the pass-through elements or replacing the sensor usually solves this issue.
E6 draws attention to the incorrect operation of the water purity sensor. Sometimes the situation can be remedied by replacing burnt contacts, but more often than not, an element simply has to be replaced with a new one.
The performance of the sensors can be checked independently, but a professional master will do it more accurately, in addition, he always has the set of the necessary tool with him
E14 indicates a malfunction of the sensor responsible for the amount of water entering the dishwasher tank. It is not advisable to change or repair it yourself. Let an employee at the Bosch service center invited to your home
Error with code E15 Bosch’s dishwasher indicates that the Aquastop integrated system is malfunctioning and the sensor is detecting leaks. In this case, you need to inspect the unit pan, hoses and adjacent elements to detect a problem area. When it is found, the problem can only be eliminated by replacing or repairing the failed part. We recommend that you familiarize yourself with information on where to look and how to choose high-quality spare parts for dishwashers.
The video presents what the error E15 means in the Bosch dishwashers, and briefly explains how to eliminate the problem and restore the machine to working:
Key Causes of Common Faults
Even such reliable equipment as Bosch can fail for completely banal, everyday reasons, for example, due to loading excessively dirty dishes into the washing chamber. Food debris washed away by a stream of water will clog the filter and cause clogging.
If the loaded dishes are too dirty and oily, the unit will not be able to wash it properly, and the hostess will have to rinse the plates and cups manually further
To avoid this situation, it is better to first clean the food left on the plates, and only then put them in the car.
Bad effect on the dishwasher incorrect connection to the mains and a faulty outlet. Too long a drain hose or poor-quality fastening in the water supply area can also create problems, so installation and installation should be entrusted to professionals.
If the home master wants to do this on his own, it is necessary to strictly follow the installation instructions and strictly follow the requirements prescribed by the manufacturer in the passport attached to the unit.
Dishwasher detergent should have a normal shelf life. It is recommended to buy it in a specialized store where the rules for storing household chemicals are followed
A lot of inconvenience, and as a consequence of problems, is created by improper loading of dishes in the washing chamber. Many users do not pay attention to this item and then encounter various problems.
In order for the washing process to proceed in normal mode, the dishes in the sections must be placed compactly. Then it will not interfere with the rotation of the irrigation arms, the timely opening of the dispenser, the free passage and uniform drainage of water
Before loading plates, cups and appliances, it is necessary to carefully study the instructions for loading dishes and take into account all the wishes put forward by the manufacturer of the equipment.
Dishes placed correctly will be perfectly washed and will not require any additional actions from the hostess. At the same time, the machine will not feel overload and will serve perfectly throughout the entire operational period.
We recommend that you familiarize yourself with the operating instructions for the Bosch dishwasher in order to avoid further problems in connection with their violation.
Video about dishwasher-specific malfunctions and how to deal with them:
How to repair a Bosch dishwasher at home that stopped pouring water. A detailed layout of the process in steps. Useful tips and tricks from an experienced wizard.
In the Bosch brand dishwasher, the circular pump failed. The video will tell you what to do in this case: a way to disassemble the unit to quickly fix the problem:
Bosch dishwasher technology is reliable and works great throughout the entire operating period. Failures and malfunctions most often occur in it due to user actions.
To avoid these points, it is worthwhile to be more attentive to the device and regularly carry out preventive measures. If a problem occurs, you can try to fix it yourself or contact a service center and entrust the work to professionals.
Want to talk about your experience in repairing a Bosch brand dishwasher? Or do you want to supplement our material with information that we did not mention in this publication? Write your additions, comments and recommendations in the block below the article.